Product Description
Includes
- Gundam MK-II (Titans)
- 2 Beam Sabers
- Vulcan Pod System
- Test Type parts
- Shoulder armor
- Chest intake
- Thigh vernier
- Manipulators
- Fists (1 pair)
- Articulated 3+1+1 (1 pair)
- Trigger-finger (right)
- Open-palm (left)
- Beam Rifle
- Extra E-cap
- Shield
- Missile Pod
- Hyper Bazooka
- Bazooka Magazine
- 1/144 Titans pilot figurine
- Adapter for Action Base
Kit Features & Gimmicks
- Gundam Mk-II can be built with either the default or the test type parts.
Articulation
- The head can swivel on a single ball-and-socket joint, or slightly pivot (in a limited extent) frontwards or backwards.
- The torso can tilt frontwards/backwards in an extent.
- The shoulder joints can swing frontward of raise upwards.
- The arms can...
- Swing on an intergrated joint frame.
- Raise horizontally.
- The upper arms can rotate.
- Both the elbow and knees are double-jointed.
- The manipulators can swivel on a ball-and-socket joint.
- The poseable hands feature 3+1+1 articulation on the fingers.
- The waist joint can only rotate in a very limited extent.
- Front, side, and rear skirt armors can pivot to avoid interference with the leg articulation.
- The hip joint axis can swing down for an expanded range of leg motion.
- The upper thighs can swing frontward/backward on a peg, raise horizontally and/or rotate on each piece.
- The ankle joints can tilt (in an extent) and/or pivot.
Weapons/Other Gimmicks
- Cockpit hatch can be optionally opened.
- The hands are swappable.
- Each of the weapons must be wielded by their respective hand parts.
- The vernier thrusters/beam saber racks on the backpack can tilt or swing frontwards/backwards on each piece.
- Beam Saber hilts can be optionally detached from the racks if one prefers to display the Mk-II holding the extra tab-molded Beam Sabers.
- Vulcan Pod System cap optionally remove from/attach onto the head.
- Beam Rifle's grip can pivot up and down.
- Beam Rifle or Bazooka Magazine can store onto both sides of the waist armor.
- Bazooka can store onto the rear waist armor via built-in connector.
- Shield can convert into storage mode.
- Gundam Mk-II can mount onto Action Base 2 (sold separately) via an adapter.
Tips & Tricks
- For better results, some of the details are needed to be panel-lined with Gundam markers.
- Topcoat (Mr. Hobby recommended) can be used to protect applied decals. (Water-based topcoat is recommended due to the kit having PP parts)
- If using matte/flat-finish top coat, it is advisable not to spray on the clear/translucent parts - can be done by masking or spraying top coat while the said parts are separated.
- For an easier PVC wire assembly on the mesh pipes, you must do a quick swipe on the pipes' edges with a fire torch. However, caution is needed to do this method, as burning the mesh pipes for an amount of time may destroy it.
Customizing-based tips
- The BPHD MS Hand 01 (or any of it's variants, though some are needed to be repainted to match the hands' colors) can be used on this Gunpla. (3mm Ball joint is required)
Notes & Trivia
- The missile pod on the shield is based on the weapon seen in the Zeta Gundam compilation films.
- The designation numbers on the Marking decals, represent each of their respective pilots:
- 01 - Emma Sheen
- 02 - Kacricon Cacooler
- 03 - Jerid Messa
- Due to being molded in a masculine build (as a result of reusing the AEUG Mk-II runners), the 1/144 figurine is actually based on either Jerid or Kacricon.
