Cement / Glues

301 - Extender Tips (6)

Extender Tip- #301 For use over BSI's standard #312 top. Can be used with all thicknesses of CA except IC-Gel. The flexible tip can be cut to the length and/or inside diameter that is needed for a particular application.

302 - EXTRA-FINE EXTENDER TIPS (6)

Extra Fine Extender Tip - #302 For use over the standard #312 top, it allows BSI's thin CAs (Insta-Cure, Insta-Flex and Super-Gold) to be applied a drop at a time. Thin CA tends to run everywhere, so these allow precise application.

303 - Extra Long Extender Tips

For use over the standard #312 top, they provide a rigid tip with extended length to get thin and gap filling CA into hard to reach areas. They are very resistant to clogging and can be cleaned by soaking in acetone.

304 - Pocket CA Extender Tips (6)

Pocket CA Extender Tip - #304 For use with BSI's Pocket CAs. It slips over the tip of the Pocket CA top to allow for finer application of the CA. With the tip, the CA can be applied to confined areas.

305 - PTFE Tubing

PTFE Tubing - #305 Two foot length of tubing can be cut off to any length (usually 2"). With one end cut at a 45° angle, can be inserted 1/8" into Pocket CA top and into #312 top if it is cut down an additional 3/64". For thin CA.

312 - EXTRA CA TOPS

Replacement top that is on all of BSI's non-Pocket CAs. Tops can be soaked in acetone overnight to remove any buildup of CA on the inside and outside of the nozzle.

313 - Extra CA Over Cap

Replacement colored cap that fits over the #312 top.

314 - Pocket Ca Top & Cap

Replacement combination of top and screw-on cap that has a built-in pin for Pocket CAs. Will fit on Pocket CA bottles only.

321 - CA Applicators Regular Tip

#321 - Regular Tip Non-clog 6" long pipette for the application of gap filling and extra-thick CA. CA is sucked up into the applicator by inserting it into an open CA bottle with the bulb at the end compressed, like an eyedropper

322 - CA Applicators Fine tip

#322 - Fine Tip Non-clog 6" long pipette for the application of thin CAs. Can also be used for the fine application of Insta-Set accelerator and for applying fine lubricating oils. CA can be kept in the applicator for two weeks.

AK-Interactive: Magnet Cyanoacrylate Glue

Fast drying, extra strong, low viscosity, specially formulated for adhesion between materials that can even have an acidic surface. Can be used with rubber, leather, wood, metal, resin and plastic. 20g

AK-Interactive: Quick Cement - Extra Thin

Special square anti rolling base. Ultra-thin precision maxoma fiber brush. 1. Special density. 2. Glue by capillary action, very quick drying. The Quick Cement is the fastest and strongest glue on the market. Unlike other plastic adhesives, it dries...

AL29682 Aleenes Turbo Tacky Glue 4oz.

Aleene's® Turbo Tacky Glue® is your go-to glue when you need a tough glue that can get the job done fast! Made with the same quality you expect from Original Tacky Glue, Turbo Tacky Glue dries up to 50% faster while featuring more resin for a superior...

AL72 Aleenes Quick Dry Tacky Glue 4oz.

When there's no time to waste, there's no time like the present to grab a bottle of Quick Dry Tacky Glue! This nontoxic adhesive tacks and dries up to 50% faster than other craft glues, drying permanent and ultra strong in as little as 35 minutes. Great...

AMMO by Mig Red Magma Liquid Cement 30ml

Cement for Plastic - Value 2 Pack - 290278

Testors Cement for Plastic 2pc- Strong, fast-drying and easy to use adhesive for polystyrene and ABS plastic. Value pack include: 2 tubes with .88 fluid ounces each and 4 gluing tips for precision application.

Clear Parts Cement & Window Maker - 281217

Use for cementing clear polystyrene; precision applicator makes easy work of gluing even small intricate builds and detailed parts.

Combo Pack Maxi Cure & Insta-Set - 157H

Bob Smith Industries has created a unique combo pack that contains a 1 oz. bottle of its extra thick Maxi-Cure CA in a Pocket CA bottle with a 2 oz. spray bottle of its Insta-Set Accelerator and two #304 extender tips. This combo pack is great for those...

Contacta - REV39602

Revell Contacta in the tube is gel-like. This has the advantage that large model parts can be precisely aligned without drying out immediately. Special properties: With plastic welding effect Gel-like consistency of the adhesive Suitable for aligning...

Contacta Liquid - REV39601

A typical plastic model adhesive works with the welding effect. This means that it dissolves the plastic and thus bonds the areas very firmly together. Revell Contacta Liquid is a super-thin liquid adhesive that is applied with a brush. The adhesive is...

Contacta Liquid Special - REV39606

Revell Contacta Liquid Special is a special chrome adhesive, but it can be used very universally. As the chrome layer prevents the welding effect, you either scrape off the chrome layer or - much more elegantly - use the special adhesive from Revell...

Contacta Professional - REV39604

Revell Contacta Professional for precise gluing. With the needle-fine cannula, micro-precise bonding can be carried out on tiny details and on the edges of transparent parts. Special properties: With plastic welding effect Liquid consistency of the...

Expositor Night Blue Cement - Mig 2045

Hold the parts together, apply the cement to the joint and allow it draw itself into the gap by capillary action. Its blue colour stands out against the plastic surface, clearly showing where it is being applied. This also allows you be sure the entire...

Extra Thin Cement (Super Quick-Setting) - 87182

Tamiya Extra Thin Cement is a widely popular glue among modelers around the world. You will find it in most modeler’s workshops. This version is the “quick setting” variant that dries around 4 times faster than the original Tamiya Extra Thin Cement,...

Extra-Thin Cement - 87038

Tamiya EXTRA THIN model cement is used to glue together plastic model kits that use polystyrene plastic. No crevice is too small for this flowing adhesive, which was developed to flow into and stick the small spaces between two plastic parts which have...

Finish-Cure™ Epoxy

FINISH-CURE™ 20 min. epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and paint. FINISH-CURE™ can be sanded the easiest of all our...

Foam-Cure™ 1 Fl. oz (30 ml) - BSI141

FOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it’s curing. To...

Foam-Cure™ 4fl. oz. (120 ml) (Clamshell) - BSI142

FOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it’s curing. To...

Grip-It Grip Glue 1oz. - Clamshell - BSI222H

Grip-it™ has been specifically formulated for applying grips and mats for recreational vehicles. Grip-It™ works great on all makes of grips for motorcycles, jet skis, snowmobiles and bicycles. Grip-It™ has a 10-25 second working time and the grip is...

IC-2000™ Rubber-toughened CA 1/2oz - BSI117

IC-2000™ is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. For model...

IC-Gel™ CA Paste (Clamshell) 20 gram Aluminum Tube - BSI116H

IC-GEL™ is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE™. IC-GEL™, however, can be applied to a vertical surface and will stay in...

IC-Gel™ CA Paste 20 gram (.7 oz.) - BSI116

IC-GEL™ is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE™. IC-GEL™, however, can be applied to a vertical surface and will stay in...

IC-Gel™ CA Paste 50g (1.75 oz.) - BSI 115

IC-GEL™ is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE™. IC-GEL™, however, can be applied to a vertical surface and will stay in...

IC-Loc™ Blue BSI -171 / 172

IC-LOC™ Blue is a medium thickness, medium strength threadlock that is applied to the threads of fasteners before assembly. Once the IC-LOC Blue™ is cured, the fasteners can be disassembled with standard hand tools if required.

IC-Loc™ Green BSI - 175 / 176

IC-LOC™ Green is a thin, medium-high strength threadlock that is applied to fasteners that are already assembled. IC-LOC Green™ wicks down into the threads of fasteners using capillary action and has good performance even with oil coated fasteners.

IC-Loc™ Purple 10ml BSI-177

IC-LOC™ Purple prevents loosening of small fasteners from normal use and vibration, but parts can still be disassembled with hand tools. IC-LOC™ Purple seals and prevents rusting of threads.

IC-Loc™ Red BSI - 173 / 174

IC-LOC™ Red is a medium thickness, high strength threadlock that is applied to the threads of fasteners before assembly. Once the IC-LOC Red™ is cured, the fasteners are permanently together and cannot be disassembled. IC-LOC Red™ will maintain its...

Insta Cure CA: 1/2 oz. - BSI101

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At...

Insta Cure CA: 1oz - BSI102

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At...

Insta Cure CA: 2oz - BSI103

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At...